![]() However, before you perform this inspection, you must locate the manual propane switch-off valve in case the electronic gas valve is in the system. If the wire starts sparking towards the metal part of your refrigerator, it’s an indication that the electrode is damaged. To check the electrode, you need to disconnect the connecting spark wire from it and set the controls at an angle where sparking happens. For this reason, you should check the electrode, and if it appears broken or damaged, replacing it is the solution. So, when the electrode is cracked or wet, it will simply ground out, and the igniter will sense that the flame is already lit, resulting in no spark. For instance, many people don’t know that an igniter senses the resistance between the electrode and a burner to create a spark. In the majority of cases, the users aren’t aware of the functionality of different components, which actually makes it challenging to fix the problem. On the other hand, if there is no clicking sound, the igniter is bad and needs to be replaced immediately to make sure the refrigerator works properly. If there is an internal click in the igniter, the igniter is working fine. Once all the wires are disconnected, apply 12V power to the G and + terminals of your igniter to check the polarity. To perform the test on your igniter, you will need to pull it out of your refrigerator and disconnect all the wires. Also, it’s best to hire a technician for installing a new igniter to ensure all the connections are well-made. Replacing the igniter is quite convenient and affordable. If that’s the case, you need to get the igniter replaced to optimize the refrigerator’s performance. However, there are instances when troubleshooting doesn’t work as the main part is not working. This is important because your igniter won’t work until it is supplied with an adequate power supply.įollowing the previous solutions is highly likely to resolve the matter. ![]() However, if you have had this battery system for years, now is the time to get a battery replacement. If you have recently purchased the battery, the issue could be with your power cables. In such a case, the only solution is to replace the power cables or the battery system as a whole. If the igniter works optimally with shore power, there is something wrong with the battery. ![]() To check whether or not you have battery issues, try connecting your motorhome to shore power. However, if the power supply is weak, the igniter won’t create a spark strong enough for the flame. The igniter circuit is powered by the battery, which gets amplified and creates a spark for the flame. If you’re getting weak sparks from the igniter, it might be because the battery is not supplying the igniter with enough power to spark the flame. You can also hire an electrician to check the entire wiring system of the refrigerator, including wires, connectors, plugs, and control boards, to devise a long-term solution. So, it’s essential to check the integrity of the cables, and if they appear damaged, they need to be replaced. This is because the voltage fluctuations and regular use often wear down the cables. If you’re on the gas mode, you will only get a reading within the first 40 seconds of using the ignition.ĭepending upon the reading on the measuring tool, you might have to change the whole circuit board or some wires if the issue is related to the solenoid. Ideally, you should get a reading from both the terminal and the solenoid section of the device. You can also use a multimeter to find out if there is any voltage present at the terminal or not. After cleaning the connectors, there are chances that the igniter will start working again, only if the igniter is not defective. ![]() Keep in mind that on-time cleaning is essential as a minor flake of rust can fuse the whole system.įor this reason, the first step should be disassembling the refrigerator system and inspecting the igniter-related connectors and components. If they are too dirty to be cleaned with a cloth, try using the baking soda paste to clean these connectors. If you have had this refrigerator for a while, you should try cleaning the connectors that are connected to the igniter and main control board. How to Fix a Dometic Refrigerator Igniter Not Working? However, you will often see customers bringing up complaints regarding the Dometic Refrigerator igniter not working. These fridges are energy efficient, and depending upon the model they might also be compatible with different power sources. This unique absorption system makes it a perfect fit for a motorhome. Unlike other refrigerators, the Dometic products use a unique system to cool your beverages and other food products. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |